Mail & Phone

Automatic Sampling System PNS DMC

Automatic sampling system for continuously monitoring particulate matter (PM10, PM2.5 or PM1) with double-magazine filter changer

The sampling system PNS DMC is based on the technique of a low / medium volume sampler (LVS or MVS) and features an automatic filter changer. It is developed for installation within a 19-inch rack in a space-saving design.
It collects fine particulate matter on sampling filters according to EN 12341:2014 (PM10 and PM2.5). For this purpose, a vacuum pump draws in ambient air, and the system fractionates the airborne particles in a sampling inlet. The air containing the desired fine particulate fraction then passes through the filter, where the particles are collected and made available for subsequent gravimetric assessment or analysis. The automatic filter changer with Geneva drive and two parallel filter magazines facilitates sequential series of up to 29 sampling cycles. The volumetric flow rate is measured with an orifice plate and electronically adjusted with an accuracy of ≤ 2% deviation.

Types: PNS 18DMC-3.1 / PNS 18DMC-6.1 / PNS 24DMC-3.1 / PNS 24DMC-6.1 / PNS 29DMC-3.1 / PNS 29DMC-6.1

 

Key Features

  • Complies with EN 12341:2014 (PM10 and PM2.5)
  • For 47 mm filters
  • Electronically adjusted volumetric flow rate
  • Temperature and humidity sensors
  • Magazines with 18, 24 or 29 filter cartridges
  • RS-232 interface
  • Vented jacket pipe (optional)

Description

Design

The sampling system PNS DMC is based on the technique of a low / medium volume sampler (LVS or MVS) and features an automatic filter changer. It is developed for installation within a 19-inch rack in a space-saving design.

The components consists of the following principal parts:

  • Stainless steel cabinet with lockable door
  • Control unit with electronic modules, SD card reader and RS-232C interface
  • Vacuum pump
  • Orifice plate
  • Filter changer unit with Geneva drive and filter magazine holders
  • 2 parallel filter magazines (capacity 18, 24 or 29 filters each)
  • Aluminum intake tube (anodized, polished inside, diameter 40 mm, length 800 mm, custom lengths available; optional)
  • Sampling inlet (for particulate matter fractions PM10, PM2.5, PM1 or TSP; optional)
  • Temperature and humidity sensors

The device types 3.1 are equipped with a 4 m³/h rotary vane vacuum pump. The volumetric flow rate for sampling PM10 or PM2.5 fractions is 2.3 m³/h; the maximum vacuum at the filter is 300 mbar. The maximum volumetric flow rate when glass fiber filters are being used is 3.5 m³/h. The technical predecessor LVS 3.1 is a reference device according to European standard EN 12341:2014.

The device types 6.1 are equipped with a 8 m³/h rotary vane vacuum pump and is otherwise identical. They can be operated with a maximum volumetric flow rate of approx. 5.5 m³/h. The device type is especially suitable for measuring semi-volatile organic compounds (SVOCs) and for use in conjunction with special filter materials (e.g. cellulose nitrate or Nuclepore filters). The maximum vacuum at the filter is 500 mbar. The technical predecessor MVS 6.1 is likewise a reference device according to European standard EN 12341:2014.

Operating principle

Before sampling begins, the desired settings are entered in the control unit, and the filter magazine is placed in the filter changer. Once the operating cycle is activated, sampling takes place automatically according to the set parameters. During operation the pump draws in air laden with fine particulate matter through the sampling inlet of the filter changer. The dust particles are fractionated by size in the sampling inlet with impactor. The particles of the desired fraction are then deposited on the sampling filter in the sampling position. At the end of the sampling period, the changer automatically changes the filters as described below.

The filter changer uses two cylindrical magazines with a capacity of 18, 24 or 29 filter cartridges each. The filter cartridges are arranged on top of each other in the magazine. Before use, either in the laboratory or in the sampling system, the magazines are loaded from the top. The left (holding) magazine contains the unladen filters. In the filter change operation, the unit transfers filter cartridges from the holding magazine to the sampling position. At the same time, the filter cartridge located in the sampling position and containing the laden filter is transferred to the right (sampled) magazine. The Geneva gearing allows the necessary complex movements to be performed simultaneously without any danger of collisions. A locking mechanism on the bottom of the magazines prevents the filter cartridges from falling out. For transportation purposes, the magazines have tight caps to prevent contamination by foreign particles. The magazine retains the top cap even while in use in the sampling system.

The volumetric flow rate is measured with an orifice plate and electronically adjusted with an accuracy of ≤ 2%. The ambient climatic conditions are continuously monitored by temperature and humidity sensors. The optional Peltier cooler ensures that the laden filter storage temperature in the unit does not exceed 23 °C.

The following data captured during sampling are saved in the internal memory. The data can be additionally backed up on an SD card or transferred to a PC by way of the RS-232 interface:

  • Serial number
  • Filter number
  • Sampling start and end date/time
  • Sampling duration in hours and minutes
  • Mean volumetric flow rate in m³/h and Nm³/h
  • Sampled volume in m³ and Nm³
  • Mean air pressure/temperature/humidity
  • Mean pressure difference at the filter
  • Filter storage temperature

Detailed information is contained in the respective datasheet.

 

The information on this website represents the state of knowledge at the time of writing. Technical specifications are subject to modifications. Comde-Derenda GmbH accepts no liability whatsoever for the content provided or for damages resulting from the use of its products.

Technical Data

Volumetric flow rate Device types 3.1 (controlled) 1.0 … 3.5 m³/h (Nm³/h)
Device types 6.1 (controlled) 1.0 … 5.5 m³/h (Nm³/h)
Accuracy ≤ 2 % deviation
Sampling duration 1 min … 1000 h
Power source 230 V, 50 / 60 Hz
Power requirement PNS DMC-3.1 approx. 300 VA
PNS DM-6.1 approx. 350 VA
Filters Filter diameter 47 mm
Sampling diameter 41 mm
Dimensions
Width 483 mm (19″ rack)
Height (without changer unit) 266 mm (6 rack units)
Height (with changer unit) 510 mm (≤ 12 rack units) /
570 mm (≤ 13 rack units) /
630 mm (≤ 15 rack units)
Required minimum height for installation 550 mm (≤ 13 rack units) /
610 mm (≤ 14 rack units) /
670 mm (∼ 15 rack units)
Depth 361 mm
Weight PNS DMC-3.1 approx. 25.5 kg
PNS DMC-6.1 approx. 27.5 kg
Interfaces RS-232 2
SD drive 1
GPRS modem (optional) 1
Sound pressure level acc. to EN 3744:2010 (distance 8 m) < 36 dB(A)
Operating temperature range -30 … +50 °C
Operating temperature range with cooling (set point value max. 23 °C) -30 … +35 °C
Operating humidity range 0 … 100 %rH

 

© 2017-2024 Comde-Derenda GmbH

Privacy Statement | Imprint